Sales Qualified and knowlegable sales people. Large Inventory. Quick delivery.
Service Industrial electronic repair service, Quick turn-around. Best price and warranty in the industry.
Support Need a product catalog? Quote? Application engineering help?
DME HOT RUNNER CONTROL REPAIR SERVICE
Temtron specializes in DME hot runner repair. We can repair all of your controls, mainframes, and cables. Standard repair pricing is available on DME controllers. We offer a low price guarantee. All DME hot runner repair and calibration tasks are performed in-house with equipment traceable to the National Institute of Standards and Technology . As with all of our other repair service, DME hot runner service comes with our full 1 year warranty.
Ask about our Low Price Guarantee
FC10D
FC10A
DSS15G
SSM15G
CSS15G
FC100G
SMP10G
SSM1502
Repair Service of these DME Hot Runner system model numbers
DME Control Model Numbers
Mainframes
Control Board
062U
DSS-15-G
FC15A
FCX10S
PMR10
SMP15G
MFHP2G
SSM15G1
CMP10
FC10
FC15AG
FCX10DSG
PMR15
SMP30
MFHP3G
CMP15
FC10A
FC15DG
MFPR-2G
PSS15
SSH-10-02
MFHP5G
Pyrometer
CMP15E
FC10AG
FC30
PC-2
SBH10
SSM15
MFP-12G-W/O
TS200
CMP15G
FC10AS
FC30AS
PCP-1M
SMP10
SSM30
CMP30
FC10ASG
FC5
PEC-50S
SMP10E
SSMX15G
Heat Module
CMP10G
C10DS
FC679A10
PEC-5ES-2
SMP10G
PSS15G
CSS15G
FC10DSG
FCS-15
PFC5
SMP15
DSS-15
FC15
FCS-10
PFC5AS2
SMP15E
SPECIAL AND CUSTOM CABLES AVAILABLE
Temtron can build most special or custom cables to fit most needs. Example: Run molds equipped for INCOE using a DME Hot Runner control system or the reverse. Tell us what YOU need!
DME Hot Runner Cable Repair
New DME hot runner power and thermocouple cables can be very costly. Let Temtron repair your defective DME hot runner cables at a significant savings.
DME Hot Runner Control Repair - Advanced Techniques Used
DME Controls are Provided with a Unique Serial Number
Temtron understands that when your DME temperature control no longer operates properly or becomes damaged, you would like it repaired quickly and at a reasonable price. Over the years we have developed some repair and calibration techniques that allow us to economically repair almost all DME temperature control modules that we receive.
One example of this is our foil replacement process. Temtron has developed a process of replacing damaged printed circuit board edge connector foils during DME control repair as shown in the Before and After pictures. This allows us to perform DME control repair on units with extensive damage on the printed circuit board for like-new performance.
•
After the repair process has been completed, the number provides warranty data to ensure that you are given your full 1 year warranty
•
Ensures that the controller you sent us is the exact one we return to you.
•
Allows in-house tracking of work in progress during the repair process for faster turn around.
•
During repair, the number determines what component and hardware updates have been performed, so your control is as current as possible.
Temperature Control Modules: How to prevent damage
(1)
Control module fuses must be rated at 250 VAC, type F (fast blow). This will protect the module in the event of a shorted heater. Fuse current rating should match the module size - usually 15 or 30 amp.
(2)
The power switch should be in the “off’ position before you install or remove the module from an energized mainframe (mf switch "on"). This will prevent edge foil damage.
(3)
The fuse holder should grip the fuse ends tightly to maintain good contact. Pinch the fuse holder clips together some if the fuse is loose in the holder. Be aware of soft, easy to bend clips, as they probably will not maintain good fuse contact. Poor fuse contact can produce small electrical arcs causing pitting and oxidation, and will eventually cause premature fuse blowing.
